Shopping Cart

Quick Fix

$141.32

In stock
Clear
Compare
SKU: N/A Category:

Download PDF here

Quick Fix is a two component epoxy system that was developed to repair cracked and spalled concrete. It can be mixed with sand to repair deeper cracks, holes and spalled concrete. Can be dusted with color hardener to blend to colored concrete repairs. It is a fast setting epoxy that has the consistency of water. Mix ratio is 50/50. 2 quart kit and 2 gallon kit available.

-fast concrete surface repair
-can be tinted with a dusting of color hardener to blend to colored concrete
-can be mixed with sand for deep repairs
-consistisy of water for a very fluid application in small cracks
-creates a very hard surface
-commercial/industrial application
-foot traffic in under a hour at 70 degree temps
-very easy to use

Additional information

size

2 quart: $141.32, 2 gallon: $250.00

Reviews

There are no reviews yet.

Be the first to review “Quick Fix”

Your email address will not be published.

Download PDF

SECTION 2: HAZARDS IDENTIFICATION

HMIS HAZARD CLASSIFICATION

HEALTH:                2             FLAMMIBILITY: 2             REACTIVITY: 0             PERSONAL PROTECTIVE EQUIPMENT: G                                                                                                                                                                         

POTENTIAL HEALTH EFFECTS

EYES:

HIGH VAPOR CONCENTRATIONS CAN CAUSE SEVERE IRRITATION TO THE EYES, NOSE OR THROAT.            

SKIN:

CAN CAUSE BURNS TO THE SKIN.        

INGESTION:

LIQUID CAN CAUSE SEVERE DAMAGE TO MUCOUS MEMBRANES IF SWALLOWED.            

INHALATION:

HIGH CONCENTRATIONS OF VAPOR CAN CAUSE IRRITATION TO THE RESPIRATORY TRACT, NAUSEA AND

DIZZINESS.            

HEALTH HAZARDS (ACUTE AND CHRONIC):

PROLONGED OR REPEATED EXPOSURE MAY CAUSE ASTHMA AND SKIN SENSITIZATION OR OTHER ALLERGIC RESPONSES.      

CAN CAUSE SENTIZATION BY EXPOSURE THROUGH CONTACT OR HIGH CONCENTRATION OF VAPOR. OVER EXPOSURE TO THIS MATERIAL CAN CAUSE CARDIAC ABNORMALITIES, ANEMIA, LIVER ABNORMALITIES, KIDNEY DAMAGE OR EVEN EYE DAMAGE.   CAN CAUSE ASTHMA OR OTHER RESPIRATORY DISORDERS, BRONCHITIS, EMPHYSEMA, HYPERACTIVITY, AND EXCEMA. MAY CAUSE CANCER.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

RESPIRATORY CONDITIONS OR OTHER ALLERGIC AILMENTS      

CARCINOGENICITY

OSHA: NO                     NTP: yes                         IARC: yes

ADDITIONAL CARCINOGENICITY INFORMATION:

Product may contain ethyl benzene as a component of Aromatic Petroleum Distillates (IARC 2B)

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS                                                                                                                                                                                                                           

INGREDIENT                                                        CAS NO.                                  OSHA PEL          ACGIH TLV         OSHA STEL         WEIGHT %

 

Tetrahydroxypropylethylenediamine                  102-60-3                              NE                        NE                            NE                          

Aromatic Petroleum Distillates                           64742-95-6             100PPM                  100PPM                  NONE                    

*cumene (as a component of 64742-95-6)        98-82-8                   50ppm                    50ppm                    NONE                     (<1%)     

*1,2,4-Trimethylbenzene as a component of 64742-95-6

                                                                                95-63-6                   25ppm                    NONE                     NONE                     (<21%) *ethyl benzene (as a component of 64742-95-6          100-41-4                 100ppm                  100ppm                  125ppm                  (<0.39)

*Xylene (as a component of CAS# 64742-95-6)                1330-20-7               100PPM                  100PPM                  150PPM                  (<2%)

solvent dye                                                            N/A                          NONE                    NONE                     NONE                        <1

 

*TOXIC CHEMICAL(S) SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III AND OF 40 CFR 372.

SECTION 4: FIRST AID MEASURES

EYES:

IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES WHILE LIFTING UPPER AND LOWER LIDS, GET IMMEDIATE MEDICAL ASSISTANCE.            

SKIN:

FLUSH SKIN WITH WATER FOR AT LEAST 15 MINUTES AND REMOVE ALL CONTAMINATED CLOTHING IMMEDIATELY. GET

MEDICAL ATTENTION IF REDDENING OR SWELLING OCCURS.    

INGESTION:

DO NOT INDUCE VOMITING. DILUTE BY GIVING WATER OR MILK TO DRINK IF VICTIM IS CONSCIOUS. GET MEDICAL ATTENTION IMMEDIATELY.    

INHALATION:

REMOVE TO FRESH AIR IF EFFECTS PERSIST AND ADMINISTER OXYGEN IF NECESSARY.          

SECTION 5: FIRE-FIGHTING MEASURES

FLAMMABLE LIMITS IN AIR,                               UPPER: 7.0

   (% by volume)                                  LOWER: 1.1

FLASH POINT: 145F

METHOD USED:

SETA FLASH            

EXTINGUISHING MEDIA:

FOAM, ALCOHOL FOAM, CO2  

SPECIAL FIRE FIGHTING PROCEDURES:

TOXIC FUMES WILL BE EVOLVED WHEN THIS MATERIAL IS INVOLVED IN A FIRE. A SELF-CONTAINED BREATHING APPARATUS SHOULD BE AVAILABLE FOR FIRE FIGHTERS.        

UNUSUAL FIRE AND EXPLOSION HAZARDS:

NONE KNOWN      

SECTION 6: RELEASE MEASURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: AVOID CONTACT WITH MATERIAL. WEAR THE APPROPRIATE SAFETY EQUIPMENT. STOP SPILL AT SOURCE, DYKE AREA TO PREVENT SPREADING. PUMP LIQUID TO SALVAGE TANK. TAKE UP REMAINDER WITH CLAY OR OTHER ABSORBANT AND PLACE IN DISPOSAL CONTAINERS.

SECTION 7: HANDLING AND STORAGE

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

AVOID ALL SKIN CONTACT. AVOID BREATHING VAPORS. RESEAL PARTIALLY USED CONTAINERS. PROPERLY LABEL ALL CONTAINERS. WASH WITH SOAP AND WATER BEFORE EATING, DRINKING, SMOKING, OR USING TOILET FACILITIES. OBSERVE CONDITIONS OF GOOD INDUSTRIAL HYGIENE AND SAFE WORKING PRACTICES.    

OTHER PRECAUTIONS:

MIXED MATERIALS CONTAIN THE HAZARDS OF ALL THE COMPONENTS, THEREFORE, READ THE MSDS OF ALL COMPONENTS TO BECOME FAMILIAR WITH ALL HAZARDS PRIOR TO USING THIS PRODUCT.      

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

RESPIRATORY PROTECTION:

NIOSH APPROVED RESPIRATOR PROTECTION REQUIRED IN THE ABSENCE OF PROPER ENVIRONMENTAL CONTROLS. FOR EMERGENCIES A SELF-CONTAINED BREATHING APPARATUS OR A FULL FACE RESPIRATOR IS RECOMMENDED.      

VENTILATION:

AVOID BREATHING VAPORS. VENTILATION MUST BE SUFFICIENT TO CONTROL VAPORS.      

PROTECTIVE GLOVES:

IMPERVIOUS GLOVES, NEOPRENE OR RUBBER.      

EYE PROTECTION:

SPLASH PROOF GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS.      

OTHER PROTECTIVE CLOTHING OR EQUIPMENT:

CLEAN BODY COVERING CLOTHING AS WELL AS APRON FOOTWEAR OR OTHER EQUIPMENT SHOULD BE USED AS DEEMED NECESSARY TO AVOID CONTACT WITH THE MATERIAL.      

WORK HYGIENIC PRACTICES:

OBSERVE GENERAL GOOD HYGIENIC PRACTICES.                                                                                                      

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE AND ODOR: DARK TRANSPARENT BLUE COLOR LIQUID WITH AROMATIC SOLVENT ODOR      

BOILING POINT OR RANGE:  N/A  

VAPOR DENSITY (AIR = 1):   Not available        

SPECIFIC GRAVITY (H2O = 1): 0.93                        

EVAPORATION RATE: N/A      

SOLUBILITY IN WATER: NEGLIGIBLE

SECTION 10: STABILITY AND REACTIVITY

 

STABILITY:

STABLE      

CONDITIONS TO AVOID (STABILITY):

AVOID CONTACT WITH OPEN FLAMES AND ALL SOURCES OF IGNITIONS AND SPARKS.      

INCOMPATIBILITY (MATERIAL TO AVOID):

AVOID CONTACT WITH STRONG OXIDIZING AGENTS OR MATERIALS    

HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:

CO, CO2, NOX, AMINES AND OTHER ALIPHATIC FRAGMENTS WHICH HAVE NOT BEEN DETERMINED.      

HAZARDOUS POLYMERIZATION:

WILL NOT OCCUR      

SECTION 11: TOXICOLOGICAL INFORMATION

 

Component CAS# 64742-95-6 Test on similar materials show a low order of acute oral and dermal toxicity. May cause eye irritation, may cause irritation on skin and mucous membranes.

Component Ethyl Benzene ( a minor component of CAS# 64742-96-6): Acute Oral toxicity LD50: ca. 3500 mg/kg (rat); Acute inhalation LC50: 17.2 mg/l 4h (rat); Acute Dermal Toxicity: 17,800 mg/kg (rabbit); Skin Irritation rabbit Draize exposure time 24h – slightly irritating. Eye Irritation rabbit Draize – severely irritating. Sensitization dermal (human patch test) non-sensitizer.Repeated Dose toxicity 28 days inhalation NOAEL: 3.4 mg/l (rabbit). Mutagenicity Genetic Toxicity in Vitro: Ames: Negative (salmonella typhimurium, metabolic activation with/without). Carcinogenecity: Ethyl benzene was tested by inhalation exposure in mice and rats. Ibn mice, there was an increased incidence of lung adenomas in males and liver adenomas in females. In male rats, there was an increased incidence of renal tubule adenomas and carcinomas. Two Studies of workers potentially exposed to ethyl benzene in a production plant and a styrene polymerization plant, showed no excess cancer incidence and no excess cancer mortalitry during a 15 year follow-up. Toxicity to Reproduction/Fertility: Inhalation (monkey, male) Reproductive effects have been observed in animal studies, In a generation study, inhalation (rat/female) NOAEL (parental): 100ppm NOAEL (F2): 100ppm. Developmental Toxicity/Teratogenicity rat, female, inhalation, gestation, daily, NOAEL (teratogenicity): 100ppm (maternal): 100ppm. Tratogenetic effects seen only with maternal toxicity., Fetotoxicity seen only with maternal toxicity. Rabbit, female, inhalation, gestation, daily, NOAEL (teratogenicity) < 1000 mg/m3, NOAEL (maternal) < 1000 mg/m3.

Component Xylene (a minor component of CAS# 64742-95-6): Inhalation LC50 26800ppm, Skin LD50 2000 mg/kg, Ingestion LD50 4.3 g/kg. Exposure may effect skin, eye, liver, kidney, nervous system, respiratory system and lungs. High concentrations may lead to nervous system effects. Repeated overexposure has produced toxic effects in developing and young laboratory animals. Aspiration into lungs when swallowed or vomited may cause chemical pneumonitis which can be fatal.

Component Cumene( a minor componebt of CAS# 64742-95-6): IARC has classified Cumene as possibly Carcinogenic to humans (group 2B).

Component CAS# 95-63-6: Oral LD50 (rat) = 5000 mg/kg. Inhalation LC50 (rat) -4h = 18000 mg/m3.

Component Tetrahydroxypropylethylenediamine CAS# 102-60-3: Oral LD50 3280 mg/kg (rat). Skin Irritation – non irritant (rabbit). Eye Irritation – non-irritant (rabbit). Sensitization – Non-sensitizing (guinea pig, maximization test). Genetic Toxicity – The component was not mutagenic in bacteria.

 

SECTION 12: ECOLOGICAL INFORMATION

 

Component CAS# 64742-95-6 Toxic to aquatic organisms.

Component Ethyl Benzene (a minor component of CAS# 64742-95-6): Biodegradation, Aerobic, 50%, Exposure time 28 days. .Biochemical Oxygen demand (BOD) 5 days, 2.8% and 35 days, 1780 mg/g. Bioaccumulation: Cyprinus carpio (Carp), 15 BCF. Acute and Prolonged Toxicity to Fish LC50: 12.1 mg/l (fathead minnow, 96 h). Acute Toxicity to Aquatic Invertebrates EC50: 1.8-2.9 mg/l (water flea, 48 h). Toxicity to Aquatic Plants EC50: 4.6 mg/l (green algae, 72 h). Toxicity to microorganisms EC50: 130 mg/l (activated sludge microorganisms, 48 hr).

Component Xylene (a minor component of CAS# 64742-95-6): Acute Toxicity: Fish: Toxic 1 < LCECIC50 < 10mg/l, Aquatic Invertabrates: Toxic 1 < LC/EC/IC50 <10mg/l, Algae: Toxic 1 < LC/EC/IC50 <10 mg/l. Mobility – floats on water. If it enters the soil it will be highly mobile and may contaminate groundwater. Oxidises rapidly by photo-chemical reactions in air.

Component Cumene (a minor component of CAS# 64742-95-6): LC50 (fish) 1-10 mg/l.

Component CAS# 95-63-6: Toxicity to fish LC50 (fathead minnow) 7.72 mg/l 96 hr. Toxicity to daphnia and other aquatic invertebrates: Immobilization EC50 (water flea) 3.6mg/l 48hr.

Component Tetrahydroxypropylethylenediamine CAS# 102-60-3 : Test Method OECD 301 A (aerobic) activated sludge : DOC Reduction 40-50%, 42 days.Toxicity to microorganisms : OECD Guideline 209 aerobic, activated sludge : 1000 mg/l (30 min), The inhibition of the degradation activity of activated sludge is not anticipated when introduced to bilogical treatment plants in appropriate low concentrations.

SECTION 13: WASTE DISPOSAL

WASTE DISPOSAL METHOD:

DISPOSE OF MATERIAL AS A HAZARDOUS WASTE ACCORDING TO FEDERAL, STATE, AND LOCAL REGULATIONS.

 

SECTION 14: Transport Information

DOT: UN1993, FLAMMABLE LIQUID N.O.S..(CONTAINS AROMATIC PETROLEUM DISTILLATES), 3, PGIII

 

IMO/IMDG: UN1993, FLAMMABLE LIQUID N.O.S..(CONTAINS AROMATIC PETROLEUM DISTILLATES), 3, PGIII

SECTION 15: REGULATORY INFORMATION

 

Component CAS# 64742-95-6 This product is a hazardous chemical . This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372 Component 1,2,4-trimethylbenzene CAS# 95-63-6 at < 42% and xylene CAS# 1330-20-7 at < 3.0%, Cumene CAS# 98-82-8 at < 2%, and Ethylbenzene CAS# 100-41-4 at < 0.40%.. This component contains chemicals on the California Proposition 65 list that may cause cancer or reproductive harm. Component is on the TSCA list as well as the AICS, DSL, ECL, EINECS, ENCS, IECSC and PICCS lists

Component Ethyl Benzene (a minor component of CAS# 64742-95-6): US EPA CERCLA Hazardous Substances (40 CFR 302): Ethyl Benzene reportable quantity 1000 lbs. US EPA Emergency Planning and Community Right to Know Act (EPCRA) SARA Title III Section 313 Toxic Chemicals (40 CFR 372.5) components, Ethyl Benzene. California Prop 65: This product contains chemicals known to the State of California to be carcinogenic: Ethyl Benzene CAS# 100-41-4 @ 0.39% Massachusetts, New York, Pennsylvania Right to Know list includes the following components: Ethyl Benzene CAS# 100-41-4. Massachusetts, New York, Pennsylvania Special hazardous Substance includes the following components: Ethyl Benzene CAS# 100-41-4

Component Xylene (a minor component of CAS# 64742-95-6): Xylene contains EPCRA section 313 chemicals subject to the reporting requirements of the emergency planning and community right to know act of 1968. Xylene and its components are on the California Proposition 65 list for developmental toxicity, Reproductive toxicity and carcinogen list. Ingredients are on the TSCA list, DSL Canada, AICS, China, EINECS, ENCS, Korea, New Zealand, Phillipines inventory lists and on the Massachusetts, New Jersey, Pennsylvania right to know lists

Component Cumene (a minor componebt of CAS# 64742-95-6): is a SARA 313 chemical. This component is a CERCLA chemical. This component is a California Proposition 65 Chemical which is known to cause cancer or other birth defects or reproductive harm. This component is on the New Jersey right to know list. Component is on the TSCA list and Canada DSL list.

Component CAS# 95-63-6: This component is subject to SARA Title III Section 313 reporting. This component is in the TSCA and Canada DSL Lists. This component is on the Massachusetts, Pennsylvania, New Jersey right to know lists.

Component Tetrahydroxypropylethylenediamine CAS# 102-60-3: Component is on the TSCA and canada DSL lists. This component may contain chemicals known to the State of California to cause cancer.

SECTION 16: OTHER INFORMATION

DISCLAIMER: THE INFORMATION HERE IN IS BASED ON THE DATA AVAILABLE AND IS BELIEVED TO BE ACCURATE, HOWEVER, THE MANUFACTURER MAKES NO WARRANTY EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THIS DATA OR THE RESULTS OBTAINED FROM THE USE THEREOF. ACCORDINGLY, WE ASSUME NO RESPONSIBILITY FOR INJURY FROM THE USE OF THIS PRODUCT.

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME:       NP343 PART A

PRODUCT CODES:       343 A

MANUFACTURER: National Polymers Inc.      

STREET ADDRESS: 9 Guttman Avenue                    

CITY, STATE, ZIP: Charleroi, Pa. 15022                  

INFORMATION PHONE:   724-483-9300

EMERGENCY PHONE:   Chemtrec 800-424-9300

FAX PHONE: 724-483-9306                

PREPARED BY: Harry Jackson          

DATE REVISED:   1/2/13

SECTION 2: HAZARDS IDENTIFICATION

HMIS HAZARD CLASSIFICATION

HEALTH:                2             FLAMMIBILITY: 2             REACTIVITY: 1             PERSONAL PROTECTIVE EQUIPMENT: G                                                                                                                                                                    

POTENTIAL HEALTH EFFECTS

EYES:

WILL CAUSE BURNS TO THE EYES. HIGH VAPOR CONCENTRATIONS CAN CAUSE SEVERE IRRITATION TO THE EYES.            

SKIN:

WILL CAUSE BURNS TO THE SKIN        

INGESTION:

LIQUID CAN CAUSE SEVERE DAMAGE TO MUCOUS MEMBRANES IF SWALLOWED.            

INHALATION:

HIGH CONCENTRATIONS OF VAPOR CAN CAUSE IRRITATION TO THE RESPIRATORY TRACT, NAUSEA AND DIZZINESS.            

HEALTH HAZARDS (ACUTE AND CHRONIC):

PROLONGED OR REPEATED EXPOSURE MAY CAUSE ASTHMA AND SKIN SENSITIZATION OR OTHER ALLERGIC RESPONSES.    

CAN CAUSE SENTIZATION BY EXPOSURE THROUGH CONTACT OR HIGH CONCENTRATION OF VAPOR. OVER EXPOSURE TO THIS MATERIAL CAN CAUSE CARDIAC ABNORMALITIES, ANEMIA, LIVER ABNORMALITIES, KIDNEY DAMAGE OR EVEN EYE DAMAGE.   CAN CAUSE ASTHMA OR OTHER RESPIRATORY DISORDERS, BRONCHITIS, EMPHYSEMA, HYPERACTIVITY, AND EXCEMA.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

RESPIRATORY CONDITIONS OR OTHER ALLERGIC AILMENTS    

CARCINOGENICITY

OSHA:   NO                      NTP:   yes                         IARC:   yes

ADDITIONAL CARCINOGENICITY INFORMATION:      

Product may contain ethyl benzene as a component of Aromatic Petroleum Distillates (IARC 2B)

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS                                                                                                                                                                                                                  

INGREDIENT                                                        CAS NO.                                  OSHA PEL           ACGIH TLV           OSHA STEL           WEIGHT %

HIGHER OLIGOMERS OF MDI                            9016-87-9               NONE                NONE                   NONE                  

*4, 4-DIPHENYLMETHANE DIISOCYANATE      101-68-8                 NONE                 .005PPM               0.02ppm                      30

Aromatic Petroleum Distillates                           64742-95-6             100PPM                  100PPM                  NONE                    

*cumene (as a component of 64742-95-6)        98-82-8                   50ppm                    50ppm                    NONE                     (<1%)     

*1,2,4-Trimethylbenzene as a component of 64742-95-6

                                                                                95-63-6                   25ppm                    NONE                     NONE                     (<21%) *ethyl benzene (as a component of 64742-95-6          100-41-4                 100ppm                  100ppm                  125ppm                  (<0.39)

*Xylene (as a component of CAS# 64742-95-6)                1330-20-7               100PPM                  100PPM                  150PPM                  (<2%)

 

*INDICATES TOXIC CHEMICAL(S) SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III AND OF 40 CFR 372.      

 

SECTION 4: FIRST AID MEASURES

 

EYES:

IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES WHILE LIFTING UPPER AND LOWER LIDS. GET IMMEDIATE MEDICAL ASSISTANCE.            

SKIN:

FLUSH SKIN WITH WATER FOR AT LEAST 15 MINUTES AND REMOVE ALL CONTAMINATED CLOTHING IMMEDIATELY. GET MEDICAL ATTENTION IF REDDENING OR SWELLING OCCURS.    

INGESTION:

DO NOT INDUCE VOMITING. DILUTE BY GIVING WATER OR MILK TO DRINK IF VICTIM IS CONSCIOUS. GET MEDICAL ATTENTION IMMEDIATELY.    

INHALATION:

REMOVE TO FRESH AIR IF EFFECTS PERSIST AND ADMINISTER OXYGEN IF NECESSARY.

 

SECTION 5: FIRE-FIGHTING MEASURES

 

FLAMMABLE LIMITS IN AIR,                               UPPER:   7.0

   (% by volume)                                 LOWER:   0.4

FLASH POINT: 199F

METHOD USED:

SETA FLASH            

EXTINGUISHING MEDIA:

FOAM, ALCOHOL FOAM, CO2      

SPECIAL FIRE FIGHTING PROCEDURES:

TOXIC FUMES WILL BE EVOLVED WHEN THIS MATERIAL IS INVOLVED IN A FIRE. A SELF-CONTAINED BREATHING APPARATUS SHOULD BE AVAILABLE FOR FIRE FIGHTERS.        

UNUSUAL FIRE AND EXPLOSION HAZARDS:

NONE KNOWN

 

SECTION 6: RELEASE MEASURES

 

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

AVOID CONTACT WITH MATERIAL. WEAR THE APPROPRIATE SAFETY EQUIPMENT. STOP SPILL AT SOURCE, DYKE AREA TO PREVENT SPREADING. PUMP LIQUID TO SALVAGE TANK. TAKE UP REMAINDER WITH CLAY OR OTHER ABSORBANT AND PLACE IN DISPOSAL CONTAINERS.

 

SECTION 7: HANDLING AND STORAGE

 

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

AVOID ALL SKIN CONTACT. AVOID BREATHING VAPORS. RESEAL PARTIALLY USED CONTAINERS. PROPERLY LABEL ALL CONTAINERS. WASH WITH SOAP AND WATER BEFORE EATING, DRINKING, SMOKING, OR USING TOILET FACILITIES. OBSERVE CONDITIONS OF GOOD INDUSTRIAL HYGIENE AND SAFE WORKING PRACTICES.

OTHER PRECAUTIONS:

MIXED MATERIALS CONTAIN THE HAZARDS OF ALL THE COMPONENTS, THEREFORE, READ THE MSDS OF ALL COMPONENTS TO BECOME FAMILIAR WITH ALL HAZARDS PRIOR TO USING THIS PRODUCT.    

 

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

 

RESPIRATORY PROTECTION:

NIOSH APPROVED RESPIRATOR PROTECTION REQUIRED IN THE ABSENCE OF PROPER ENVIRONMENTAL CONTROLS, FOR EMERGENCIES A SELF-CONTAINED BREATHING APPARATUS OR A FULL FACE RESPIRATOR IS RECOMMENDED.      

VENTILATION:

AVOID BREATHING VAPORS. VENTILATION MUST BE SUFFICIENT TO CONTROL VAPORS.    

PROTECTIVE GLOVES:

IMPERVIOUS GLOVES, NEOPRENE OF RUBBER.      

EYE PROTECTION:

SPLASH PROOF GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS.      

OTHER PROTECTIVE CLOTHING OR EQUIPMENT:

CLEAN BODY COVERING CLOTHING AS WELL AS APRON FOOTWEAR OR OTHER EQUIPMENT SHOULD BE USED AS DEEMED NECESSARY TO AVOID CONTACT WITH THE MATERIAL.      

WORK HYGIENIC PRACTICES:

OBSERVE GENERAL GOOD HYGIENIC PRACTICES.      

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

 

APPEARANCE AND ODOR: DARK AMBER LIQUID WITH AROMATIC SOLVENT ODOR      

BOILING POINT OR RANGE: N/A  

VAPOR DENSITY (AIR = 1):   Not available        

SPECIFIC GRAVITY (H2O = 1): 1.1    

EVAPORATION RATE:   N/A      

SOLUBILITY IN WATER: NEGLIGIBLE

 

SECTION 10: STABILITY AND REACTIVITY

 

STABILITY:

STABLE      

CONDITIONS TO AVOID (STABILITY):

AVOID CONTACT WITH OPEN FLAMES AND ALL SOURCES OF IGNITIONS AND SPARKS.    

INCOMPATIBILITY (MATERIAL TO AVOID):

AVOID CONTACT WITH STRONG OXIDIZING AGENTS, MINERAL ACIDS AND EPOXY RESINS IN UNCONTROLLED AMOUNTS.    

HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:

CO, CO2, NOX      

HAZARDOUS POLYMERIZATION:

WILL NOT OCCUR

 

SECTION 11: TOXICOLOGICAL INFORMATION

 

Component CAS# 64742-95-6 Test on similar materials show a low order of acute oral and dermal toxicity. May cause eye irritation, may cause irritation on skin and mucous membranes.

Component Ethyl Benzene ( a minor component of CAS# 64742-96-6): Acute Oral toxicity LD50: ca. 3500 mg/kg (rat); Acute inhalation LC50: 17.2 mg/l 4h (rat); Acute Dermal Toxicity: 17,800 mg/kg (rabbit); Skin Irritation rabbit Draize exposure time 24h – slightly irritating. Eye Irritation rabbit Draize – severely irritating. Sensitization dermal (human patch test) non-sensitizer.Repeated Dose toxicity 28 days inhalation NOAEL: 3.4 mg/l (rabbit). Mutagenicity Genetic Toxicity in Vitro: Ames: Negative (salmonella typhimurium, metabolic activation with/without). Carcinogenecity: Ethyl benzene was tested by inhalation exposure in mice and rats. Ibn mice, there was an increased incidence of lung adenomas in males and liver adenomas in females. In male rats, there was an increased incidence of renal tubule adenomas and carcinomas. Two Studies of workers potentially exposed to ethyl benzene in a production plant and a styrene polymerization plant, showed no excess cancer incidence and no excess cancer mortalitry during a 15 year follow-up. Toxicity to Reproduction/Fertility: Inhalation (monkey, male) Reproductive effects have been observed in animal studies, In a generation study, inhalation (rat/female) NOAEL (parental): 100ppm NOAEL (F2): 100ppm. Developmental Toxicity/Teratogenicity rat, female, inhalation, gestation, daily, NOAEL (teratogenicity): 100ppm (maternal): 100ppm. Tratogenetic effects seen only with maternal toxicity., Fetotoxicity seen only with maternal toxicity. Rabbit, female, inhalation, gestation, daily, NOAEL (teratogenicity) < 1000 mg/m3, NOAEL (maternal) < 1000 mg/m3.

Component Xylene (a minor component of CAS# 64742-95-6): Inhalation LC50 26800ppm, Skin LD50 2000 mg/kg, Ingestion LD50 4.3 g/kg. Exposure may effect skin, eye, liver, kidney, nervous system, respiratory system and lungs. High concentrations may lead to nervous system effects. Repeated overexposure has produced toxic effects in developing and young laboratory animals. Aspiration into lungs when swallowed or vomited may cause chemical pneumonitis which can be fatal.

Component Cumene( a minor componebt of CAS# 64742-95-6): IARC has classified Cumene as possibly Carcinogenic to humans (group 2B).

Component CAS# 95-63-6: Oral LD50 (rat) = 5000 mg/kg. Inhalation LC50 (rat) -4h = 18000 mg/m3.

Component HIGHER OLIGOMERS OF MDI CAS#  9016-87-9 and *4, 4-DIPHENYLMETHANE DIISOCYANATE CAS# 101-68-8: (data based on a similar product) The oral LD50 for rats is greater than 10,000 mg/kg. Skin: The LD50 for skin absorption in rabbits is greater than 9,400 mg/kg. Mutagenicity: Mutagenicity data on the MDI are inconclusive. MDI was weakly positive in some in vitro (test tube) studies; other in vitro studies were negative. A mutagenicity study in animals was negative. Ingestion: Ingestion of this product causes vomiting, nausea and abdominal pain. Single dose oral toxicity is

considered to be extremely low. No hazards anticipated from swallowing small amounts incidental to normal handling operations. The oral LD50 for rats is >10,000 mg/kg. Eye: May cause slight eye irritation. Corneal injury is unlikely. Skin:

Prolonged or repeated exposure may cause skin irritation. May stain the skin. Skin contact may result in allergic skin reactions or respiratory sensitisation but is not expected to result in absorption of amounts sufficient to cause other adverse effects. The LD50 for skin absorption in rabbits is >9400 mg/kg. CANCER INFORMATION: Lung tumours have been observed in laboratory animals exposed to aerosol droplets of MDI/Polymeric MDI (6mg/m3) for their lifetime. Tumours occurred concurrently with respiratory irritation and lung injury. Current exposure standards are expected to protect against these effects.SYSTEMIC (OTHER TARGET ORGAN) EFFECTS: Tissue injury in the upper respiratory tract and lungs has been observed in laboratory animals after repeated excessive exposures to MDI/Polymeric MDI aerosols. TERATOLOGY (BIRTH DEFECTS): In laboratory animals, Polymeric MDI did not produce birth defects, other foetal effects occurred only at high doses, which were toxic to the mother.

 

SECTION 12: ECOLOGICAL INFORMATION

 

Component CAS# 64742-95-6 Toxic to aquatic organisms.

Component Ethyl Benzene (a minor component of CAS# 64742-95-6): Biodegradation, Aerobic, 50%, Exposure time 28 days. .Biochemical Oxygen demand (BOD) 5 days, 2.8% and 35 days, 1780 mg/g. Bioaccumulation: Cyprinus carpio (Carp), 15 BCF. Acute and Prolonged Toxicity to Fish LC50: 12.1 mg/l (fathead minnow, 96 h). Acute Toxicity to Aquatic Invertebrates EC50: 1.8-2.9 mg/l (water flea, 48 h). Toxicity to Aquatic Plants EC50: 4.6 mg/l (green algae, 72 h). Toxicity to microorganisms EC50: 130 mg/l (activated sludge microorganisms, 48 hr).

Component Xylene (a minor component of CAS# 64742-95-6): Acute Toxicity: Fish: Toxic 1 < LCECIC50 < 10mg/l, Aquatic Invertabrates: Toxic 1 < LC/EC/IC50 <10mg/l, Algae: Toxic 1 < LC/EC/IC50 <10 mg/l. Mobility – floats on water. If it enters the soil it will be highly mobile and may contaminate groundwater. Oxidises rapidly by photo-chemical reactions in air.

Component Cumene (a minor component of CAS# 64742-95-6): LC50 (fish) 1-10 mg/l.

Component CAS# 95-63-6: Toxicity to fish LC50 (fathead minnow) 7.72 mg/l 96 hr. Toxicity to daphnia and other aquatic invertebrates: Immobilization EC50 (water flea) 3.6mg/l 48hr.

Component HIGHER OLIGOMERS OF MDI CAS#   9016-87-9 and *4, 4-DIPHENYLMETHANE DIISOCYANATE CAS# 101-68-8: (data based on a similar product) Movement in the environment is expected to be limited by the formation of insoluble polymers. Biodegradation is not applicable (for the isocyanate itself). Material is expected to be biodegrade only very slowly. Fails to pass OECD modified MITI test; hydrolysis products degrade slowly. Degradation is expected in the atmospheric environment. Ecotoxicity: Material is practically non-toxic to aquatic organisms on an acute basis (LD50 greater than 100 mg/l in

most sensitive species).

  

SECTION 13: WASTE DISPOSAL

 

WASTE DISPOSAL METHOD:

DISPOSE OF MATERIAL AS A HAZARDOUS WASTE ACCORDING TO FEDERAL, STATE, AND LOCAL REGULATIONS.

 

SECTION 14: Transport Information

 

DOT: UN1993, FLAMMABLE LIQUID N.O.S..(CONTAINS AROMATIC PETROLEUM DISTILLATES), 3, PGIII

 

IMO/IMDG: UN1993, FLAMMABLE LIQUID N.O.S..(CONTAINS AROMATIC PETROLEUM DISTILLATES), 3, PGIII

 

SECTION 15: REGULATORY INFORMATION

 

Component CAS# 64742-95-6 This product is a hazardous chemical . This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372 Component 1,2,4-trimethylbenzene CAS# 95-63-6 at < 42% and xylene CAS# 1330-20-7 at < 3.0%, Cumene CAS# 98-82-8 at < 2%, and Ethylbenzene CAS# 100-41-4 at < 0.40%.. This component contains chemicals on the California Proposition 65 list that may cause cancer or reproductive harm. Component is on the TSCA list as well as the AICS, DSL, ECL, EINECS, ENCS, IECSC and PICCS lists

Component Ethyl Benzene (a minor component of CAS# 64742-95-6): US EPA CERCLA Hazardous Substances (40 CFR 302): Ethyl Benzene reportable quantity 1000 lbs. US EPA Emergency Planning and Community Right to Know Act (EPCRA) SARA Title III Section 313 Toxic Chemicals (40 CFR 372.5) components, Ethyl Benzene. California Prop 65: This product contains chemicals known to the State of California to be carcinogenic: Ethyl Benzene CAS# 100-41-4 @ 0.39% Massachusetts, New York, Pennsylvania Right to Know list includes the following components: Ethyl Benzene CAS# 100-41-4. Massachusetts, New York, Pennsylvania Special hazardous Substance includes the following components: Ethyl Benzene CAS# 100-41-4

Component Xylene (a minor component of CAS# 64742-95-6): Xylene contains EPCRA section 313 chemicals subject to the reporting requirements of the emergency planning and community right to know act of 1968. Xylene and its components are on the California Proposition 65 list for developmental toxicity, Reproductive toxicity and carcinogen list. Ingredients are on the TSCA list, DSL Canada, AICS, China, EINECS, ENCS, Korea, New Zealand, Phillipines inventory lists and on the Massachusetts, New Jersey, Pennsylvania right to know lists

Component Cumene (a minor componebt of CAS# 64742-95-6): is a SARA 313 chemical. This component is a CERCLA chemical. This component is a California Proposition 65 Chemical which is known to cause cancer or other birth defects or reproductive harm. This component is on the New Jersey right to know list. Component is on the TSCA list and Canada DSL list.

Component CAS# 95-63-6: This component is subject to SARA Title III Section 313 reporting. This component is in the TSCA and Canada DSL Lists. This component is on the Massachusetts, Pennsylvania, New Jersey right to know lists.

Component HIGHER OLIGOMERS OF MDI CAS#   9016-87-9 and *4, 4-DIPHENYLMETHANE DIISOCYANATE CAS# 101-68-8: HAZARDOUS SUBSTANCES CLASSIFICATION: Harmful. Irritant. Sensitiser. RISK PHRASES: R20. Harmful by inhalation. R36/37/38. Irritating to eyes, respiratory system and skin. R42. May cause sensitisation by inhalation. Components are on the TSCA and Canada DSL lists.

SECTION 16:   OTHER INFORMATION

DISCLAIMER: THE INFORMATION HERE IN IS BASED ON THE DATA AVAILABLE AND IS BELIEVED TO BE ACCURATE, HOWEVER, THE MANUFACTURER MAKES NO WARRANTY EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THIS DATA OR THE RESULTS OBTAINED FROM THE USE THEREOF. ACCORDINGLY, WE ASSUME NO RESPONSIBILITY FOR INJURY FROM THE USE OF THIS PRODUCT.

TECHNICAL DATA- Quick Fix

CONCRETE QUICK FIX

PRODUCT DESCRIPTION:

Quick Fix patch kit consists of a two component polymer packaged with aggregate for patching and repairing concrete

RECOMMENDED FOR:

Industrial repairing of spalled concrete, holes, cracks and thresholds or uneven concrete slabs .

NOT RECOMMENDED FOR:

Expansion Joints.

SOLIDS BY WEIGHT:

Nearly 100% cured

VOLATILE ORGANIC CONTENT:

5.5 grams per liter cured

 

STANDARD COLORS:

Gray colored when mixed and cured. The gray color will not develop until the curing process takes place.

RECOMMENDED THICKNESS:

The NP343 polymer patch kit can be applied at variable thicknesses.

COVERAGE PER KIT:

Coverage is dependent on hole size or size of area to be repaired.

PACKAGING      

*Small patch kit consisting of a ½ pint of part A, ½ pint part B and ½ gallon (approx. 6.2#) of blended sand – packaged in gallon pail.

*Large patch Kit consisting of 1 pint part A, 1 pint part B and 1 gallon (approx. 12.4#) of blended sand – packaged in a 2 gallon pail.

 

MIX RATIO:

The liquid mix ratio is 1:1 by volume

SHELF LIFE:

1 year in unopened containers

 

SHORE D HARDNESS:

71

TENSILE STRENGTH:

4,500 psi

ELONGATION:

5-6%

IMPACT RESISTANCE:

excellent

ABRASION RESISTANCE:

excellent

COMPRESSIVE STRENGTH:

4,400 (as a slurry with aggregate sand)

BOND STRENGTH:

535 psi (concrete failure)

DOT CLASSIFICATION:

Part B “not regulated”

Part A “not regulated”

VISCOSITY:

Less than 30cps typical

CURE SCHEDULE:

pot life (100 gram mass) ………………………….1-4 minutes @ 700 F

recoat or topcoat…..………………………………1 hour @ 70 degrees F

light foot traffic…………………………..10-20 minutes @ 70 degrees F

(heavy traffic)… ………………………………….1 hour @ 70 degrees F

 

APPLICATION TEMPERATURE:

20-90 degrees F (lower temperatures will require additional cure time)

 

PRIMER:

Self priming

 

TOPCOAT:

None required. However, many types of products can be used as coatings or overlays for the area that has been patched.

 

LIMITATIONS:

Because of the quick cure time for this product, it is best to work with one small area at a time.

Typical working time after the three components are mixed according to directions is about 1-3 minutes..

Color stability may be affected by environmental conditions such as UV light, high humidity or chemical exposure. Product is not UV color stable.

Product may discolor if exposed to certain types of light such as sodium vapor lighting.

Final cured product colors may vary from batch to batch and be influenced the by silica aggregate when used.

Substrate temperature must be 50 F above dew point.

All new concrete must be cured for at least 30 days prior to application.

When applying material in cold areas, make sure the surface is clean and dry. Also, it is best to keep the material and aggregate sand at normal room temperature before mixing or use..

See reverse side for application instructions.

Test data based on neat resin unless otherwise noted.

Physical properties are typical values and not specifications.

See reverse side for limitations of our liability and warranty.

.

 

INSTRUCTIONS (NP343)

1) PRODUCT STORAGE:

Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be above 550 F to prevent product crystallization.

 

2) SURFACE PREPARATION:

All dirt, oil, dust, foreign contaminants and laitance must be removed to assure a trouble free bond to the substrate. For repair of spalled concrete, a stiff wire brush can be used to remove all loose concrete. After wire brushing the spalled area, remove all loose dust and debris with an industrial vacuum.

 

3) PRIMER:

The material is self-priming.

 

4) PRODUCT MIXING:

The product has a 1:1 liquid mix ratio by volume. Mix only an amount of material that can be used in 1-3 minutes. Mix the liquids (½ pint part A and ½ pint part B) for 15 seconds and immediately add in the ½ gallon blended aggregate and remix.

 

5) PRODUCT APPLICATION:

Immediately after the three components are mixed, (Product has a very short pot life), place the material into the area to be repaired with a trowel or other suitable equipment. Finally, trowel the floor to smooth out the area and remove any excess material. Allow the material to cure for ten to twenty minutes before foot traffic. For heavy equipment such as fork trucks, allow the material to cure for a half hour to an hour before using area that has been patched.

 

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY

 

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommenced herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

COPYRIGHT 2/19/15 NATIONAL POLYMERS INC.