Shopping Cart

Rejuvenate

$169.00

In stock
Browse Wishlist
Compare

Download PDF here

Rejuvenate is made up of a strong blend of aromatic and ketone solvents and surfactants. It is used to restore heavily coated existing solvent based acrylic sealers that have started to soften, fade, peel, crack, delaminate, and deteriorate. Rejuvenate also clears up white spots or blushing due to moisture content issues.

Surface Aid melts the heavily coated existing solvent based acrylic sealer, and helps restore the original appearance without adding more acrylic to allow the sealer to wear off naturally over time without stripping the existing bulk of the coating. Great for contractors to re -seal patios without layering to many coats of acrylics.

Superior ability to fix excessive coated acrylic sealer issues as opposed to expensive coating stripping.
This product re-vitalizes the existing surface without adding more acrylic.
Very fast drying time highly reduces the risk of trapped solvent or other types of moisture issues.
It’s ultra low viscosity allows for easy spraying through an acetone resistant sprayer.

  • Solvent Blend Thinner
  • Cures Blushing
  • Easily Melts Down Sealer
  • Sprayable, Quick Drying Formula

-Superior ability to fix excessive coated acrylic sealer issues as opposed to expensive coating stripping.
-This product re-vitalizes the existing surface without adding more acrylic.
-Very fast drying time highly reduces the risk of trapped solvent or other types of moisture issues.
-It’s ultra low viscosity allows for easy spraying through an acetone resistant sprayer.
-great for re sealing surfaces, that where sealed with a solvent based acrylic sealer
-great for contractors who re seal
5 gallon bucket

Reviews

There are no reviews yet.

Be the first to review “Rejuvenate”

Your email address will not be published.

Download PDF

PRECAUTIONS:

Flammable Liquid (Flash point < 20° F). Keep away from open flame and heat. Do not smoke. Avoid direct contact. Skin and eye irritation may occur.

Use in well-ventilated area. Inhalation of vapors may cause breathing difficulties.

KEEP OUT OF REACH OF CHILDREN.

Recommended for exterior use only.

FIRST AID:

Eye contact: Move victim from exposure source. Flush eyes with water for 10-15 minutes.

Skin: Remove contaminated clothing. Wash with soap and water. If irritation persists seek medical attention.

Inhalation: Move victim to fresh air immediately. Contact physician if breathing is difficult.

FOR CHEMICAL EMERGENCY

Spill, Leak, Fire, Exposure or Accident

CALL INFOTRAC- Day or Night

800-535-5053

OUTSIDE THE UNITED STATES CALL COLLECT 1-352-323-3500

HMIS: Health – 2   Flammability – 3   Reactivity – 0

Please refer to msds & technical data sheet prior to use of this product.

ATTENTION:

This container is hazardous when empty. Empty containers retain product residues (vapor and liquid). All labeled precautions must be observed. Do not re-use empty container for any purpose until commercially cleaned or reconditioned. Store empty container away from heat, sparks, and flame. Dispose of empty container according to state and federal laws. Clean up with Xylene.

FOR PROFESSIONAL USE ONLY!

VOC CONTENT: EXEMPT

DOT: Paint Related Material, 3, UN1263, PG II

Solids    0%

Drying Time        1.85 (Evaportion Rate)

Re-Coat Time     N/A

Foot Traffic         N/A

Wheel Traffic     N/A

Application Temp             50°F – 80°F

Wet Appearance              Clear

Dry Appearance               N/A

VOC Content     Exempt

Blush Resistance              N/A

Solvent Resistance          N/A

Concrete Adhesion         N/A

 

*Please note that low air and/or concrete temperatures and/or relative humidity may extend drying times. Follow recommended coverage rates for best results.

www.con-cretewerks.com

Made in the USA